Gizmo Dorks 1.75mm PC Polycarbonate Filament 1kg / 2.2lbs for 3D Printers, Transparent

The Gizmo Dorks Polycarbonate filament, also known as PC filament, is a strong thermoplastic material used in 3D printing. Polycarbonate has many uses in everyday applications. It is a good electrical insulator while having heat-resistant properties. Polycarbonate is used in data storage for compact discs, DVD’s and Blu-Ray’s. It is used in many medical applications as well as for parts in today’s advanced phones. It is commonly used in eye protection, and it is used after lamination to make bullet-proof glass.

Polycarbonate filament is such a great 3D material because of it’s strength. It is a really strong material while still maintaining temperature resistance. Polycarbonate does not shatter like plexiglass. It tends to bend and deform similar to hard rubber until it eventually breaks. It also has high optical clarity. PC absorbs a lot of moisture in the air. It is a hygroscopic material, and it is best to store in an airtight container when not in use. Even during use the material can become unprintable within a 24 hour print if in a humid environment. Therefore, keeping in an airtight container during printing as well is ideal. Dry filament will print more clear. Filament that has absorbed moisture will print white as well as pop and bubble during the print.

Extruding temperature is generally around 260°C, depending on the printer. PC slowly softens when heated, unlike PLA which has a high transition temperature. Slower print speeds are preferred as an increase in temperature is required for faster prints. Polyimide tape (Kapton) should be used on a heated bed, ~120°C. Some users prefer applying glue or superglue on a glass bed and then heating to ~120°C-130°C. Please do not inhale any fumes. Heated up superglue can release toxic fumes, so only use in a well ventilated area.

Product Features

  • Printing temperature : 255°C – 300°C depending on part and printer type
  • Print speeds : 30mm/s is ideal, can go up to 60 or 80mm/s
  • Store airtight in use and when not in use, absorbs moisture
  • Print on a heated bed
  • Only use in well ventilated areas or in a ventilated system

Visit The Website For More Information…

5PCS Nema 17 Stepper Motor Bipolar 2A 84oz.in 48mm 4-lead for 3D Printer/CNC

This is high torque Nema 17 stepper motor with 1.8 deg. step angle (200 steps/revolution).

Each phase draws 2A, allowing for a holding torque of 59Ncm(83.6oz.in). It’s very good choice for 3D printer.

Electrical Specification:

* Manufacturer Part Number: 17HS19-2004S

* Motor Type: Bipolar Stepper

* Step Angle: 1.8 deg.

* Holding Torque: 59Ncm(83.6oz.in)

* Rated Current/phase: 2.0A

* Phase Resistance: 1.4ohms

* Inductance: 3.0mH+/-20%(1KHz)

Physical Specification:

* Frame Size: 42 x 42mm

* Body Length: 47mm

* Shaft Diameter: 5mm

* Shaft Length: 19.5mm

* D-cut Length: 19.5mm

* Number of Leads: 4

* Lead Length: 225mm

* Weight: 390g

Connection:

Black(A+), Green(A-), Red(B+), Blue(B-)

Warning:

Make sure the motor connect to a constant current or chopper drive controller before you test motor.

Connecting the motor directly to a power supply will destroy the motor.

Product Features

  • 5pcs/ Package
  • 59Ncm(83.6oz.in) holding torque
  • NEMA 17 bipolar 1.65″x1.65″x1.85″ 4-wire
  • 1.8 deg. step angle(200 steps/rev)
  • Rated current 2.0A & resistance 1.4ohms

Visit The Website For More Information…

Reprap Prusa Mendel i2 3D Printer ABS Plastic Part

New: A brand-new, unused, unopened, undamaged item in its original packaging (where packaging is applicable). Packaging should be the same as what is found in a retail store, unless the item is handmade or was packaged by the manufacturer in non-retail pa

Product Features

  • Reprap Prusa Mendel i2 3D Printer ABS Plastic Part

Visit The Website For More Information…