IC3D 120mm (4.7″) Wide 10M Long Kapton (Polyimide) Tape for 3D Printer platforms

This is a 120mm (4.7″) wide by 22M long roll of Kapton tape (Polyimide). Enough to cover about 50 8×8″ glass sheets. We prefer this size since it’s easier to apply than full width sheets. Printing over heated Kapton taped glass allows for excellent adhesion of melted plastic and gives the bottom of your print a nice smooth finish. After many hours of printing, refresh your printing surface with this stuff. This tape can handle temperatures of up to about 280C. We’ve tested tape from several different manufacturers and chose the best. *** APPLICATION TIP: To minimize the seam from laying to sides down, just spray some lightly soaped water onto the glass and tape. Lay the first side down, slide to position, then squeegee the water out.

Price:

Read More

10 Pack: 8″ x 8″ x 2mil 3DXTech Polyimide Tape Sheets Kapton for 3D Printer Platforms

3DXTech Polyimide Tape Sheets: 10 Pack of 2mil sheets of 3DXTech Polyimide Tape offers an excellent print surface for 3D Printer Platforms. The polyimide tape is 2mil thick (0.05mm) with Silicone Adhesive and a PET release liner. This tape provides a smooth heat-resistant surface that easily removes once you have finished your print. Polyimide Tape offers excellent electrical insulation, high temperature resistance, and high voltage resistance. Suitable for use on Makerbot Replicator, Ultimaker, Prinrbot, Reprap, Mendel, Prusa, Up! Printers, Solidoodle as well as most other 3D Printers.

Product Features

  • Polyimide Substrate: 2mil (.002″)
  • Length: 8″
  • Width: 8″
  • Temp Range: up to 250C

Detailed Information available on our Homepage…

Extra Large 3D Printer Platform Tape Roll [7.25 inch wide x 65.5 feet long] – 3DXTech Blue Painters Tape is an excellent value and covers practically all 3D Printer platforms. Equivilent to 65 sheets at a fraction of the cost.

Extra Large 3D Printer platform tape roll. Your PLA prints will stick to this blue painters tape that is wide enough to fit practically every printer and long enough to last for months. 7.25″ wide x 65.5 feet long on a sturdy cardboard core. This will adhere to your build platform without leaving a sticky residue. Excellent value and incredibly useful. Suitable for use on Makerbot Replicator, Ultimaker, Prinrbot, Reprap, Mendel, Prusa, Up! Printers, Solidoodle as well as most other 3D Printers.

Product Features

  • Excellent value vs. Sheets
  • Excellent print surface for PLA
  • Adheres to printer plate with no seams
  • 7.25″ wide (18.4cm)
  • 65.5 feet long (20m)

Detailed Information available on our Homepage…

MakerTape – Kapton 9″x100′ 2mil for 3D Printer Platforms

MakerTape – Kapton 9″x100′ 2mil for 3D Printing. 9″ width covers 90% of the personal desktop 3D printer beds on the market including but not limited to Makerbot, Leapfrog, Robo3D, Solidoodle, Ultimaker, RepRap, XYZ, UP, and Flashforge.

Product Features

  • High Quality Polyimide Film with Silicone Adhesive
  • 9″ x 100′ – Much wider tape to cover entire build plate. No strips required.
  • 2mil Thickness. Much higher quality than other 1mil tapes.
  • High temperature resistance up to 500F

Detailed Information available on our Homepage…