- Voltage: 12v
- Power: 40w
- Material: Stainless Steel
- Diameter: 6mm
- Length: 20mm
3D Printer Controller for RAMPS 1.4 REPRAP MENDEL PRUSA for Arduino
With rules of cartesian coordinate robot and extruder.
Could control spare parts.
With heater/fan output/three thermistor MOSFET.
Integrated 5A extra safety and components protection.
Suit for 5 Pololu stepper driver plate.
Pololu plate pin socket.
I2C/SPI pin for future development.
All MOSFET with PWM pins.
Servo connector used to connect end dog, motor and lighting diode. Rated current 3A.
SD card add Kliment-Sdramps.
LED indicates heater output.
Two motor connects to Z Prusa Mendal.
Size: 11.5cm x 3cm.
THE BITS: These Micro-drill bit Extruder Nozzle Cleaners are an essential item for any 3D printer owner. Every extruder nozzle must be cleaned out from time to time. These nozzles are very difficult to clean properly. These micro dtill bits are of the highest quality, made in Japan. They are the perfect tool for the job. By using these precision drill bits, you will extend the life of your nozzle and without a doubt, produce finer prints. If you need another size or have any questions, contact us and we will take care of you.
THE TOOL: This multi-functional tool is perfect for hand cleaning the nozzle head to your 3D printer. You can use a drill to do the job, but the hand held tool is more safe. The high speeds of electric drills can cause damage to the nozzle head if the user does not have very steady hands. This tool is very easy to hold and compact at 4″ long. It comes with two double sided chucks that store inside the tool. The tool can be used for other projects or to work on your 3D printer.
THE NOZZLES: 1 each: .30mm, .40mm, .50mm Print Head For 1.75MM filament for MK7 MK8 makerbot RepRap print nozzle for ABS/PLA printers.
(1) 3D Printer Controller RAMPS 1.4
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion.
for more informations, you can check here : http://www.amazon.com/gp/product/B00JU41GQ4
(2) Mega 2560 R3
for more informations, you can check here : http://www.amazon.com/gp/product/B00E94CGTQ
(3) A4988 Stepper Motor Driver
A4988 is a complete microstepping motor driver with built-in translator for easy operation
for more informations, you can check here : http://www.amazon.com/gp/product/B00JXGT1G6
(4) LCD 12864 Graphic Smart Display Controller
This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the “smart adapter” included.
for more informations, you can check here : http://www.amazon.com/gp/product/B00L72FAZU
(1) RAMPS 1.4 x 1
(2) Mega 2560 R3 x 1
(3) A4988 Stepper Motor Driver with Heatsink x 5
(4) LCD 12864 Graphic Smart Display Controller x 1
(5) Smart Adapter x 1
(6) 30cm Cable x 2
(7) USB Cable x 1
(8) Storage Box x 1
Here is the firmware for you to use with Ramps 1.4 https://www.dropbox.com/s/56qbizg7l56k2lw/Marlin-Marlin_v1%20for%20lcd%2012864.zip Marlin for ramps 1.4 + A4988 stepper driver + LCD 12864 controller